Event Identifiers 1343-4613

Event identifier: cpqstmsg.dll - 1343 (Hex) 0x8435053f (Service Event)

Log Severity: Warning (2)

Log Message: Duplicate SCSI port found in slot %1. The current system ROM may not support this SCSI controller. You may need to update your system ROM.

Event identifier: cpqstmsg.dll - 1344 (Hex) 0x84350540 (Service Event)

Log Severity: Warning (2)

Log Message: A version mismatch has been detected with the SCSI device monitor driver (CPQSDM.SYS). The current driver version is %1.

Cause: You may not have rebooted after a Storage Agents upgrade. Always reboot the system after installing agents.

Event identifier: cpqstmsg.dll – 1346 (Hex) 0x84350540 (Service Event)

Log Severity: Warning (2)

Log Message: The SCSI controller on port %1 has been omitted. The SCSI Agent could not get the slot data for the controller.

Event identifier: cpqstmsg.dll - 1792 (Hex) 0x84350700 (Service Event)

Log Severity: Warning (2)

Log Message: The SNMP Agent is unable to generate traps due to an error during initialization.

Cause: The SNMP service might not be running. Reinstalling the agents may fix this error.

Event identifier: cpqstmsg.dll - 1795 (Hex) 0x84350703 (Service Event)

Log Severity: Warning (2)

Log Message: The SNMP Agent is older than other components. The SNMP Agent is older than the other components of the Storage Agents. Reinstall the entire Storage Agents package to correct this error.

Event identifier: cpqstmsg.dll - 1796 (Hex) 0x84350704 (Service Event)

Log Severity: Warning (2)

Log Message: The %1 Agent is older than other components. The %1 Agent is older than the other components of the Storage Agents. Reinstall the entire Storage Agents package to correct this error.

Event identifier: cpqstmsg.dll - 1800 (Hex) 0x84350708 (Service Event)

Log Severity: Warning (2)

Log Message: Unable to read security configuration information. SNMP sets have been disabled.

Cause: This can be caused by an invalid or missing configuration or by a corrupt registry. Reinstalling the Storage Agents might correct this issue.

Event identifier: cpqstmsg.dll - 1803 (Hex) 0xc435070b (Service Event)

Log Severity: Error (3)

Log Message: Unable to load a required library. This error can be caused by a corrupt or missing file. Reinstalling the Storage Agents or running the Emergency Repair procedure may correct this error.

Event identifier: cpqstmsg.dll - 1804 (Hex) 0x8435070c (Service Event)

Log Severity: Warning (2)

Log Message: The Storage SNMP Agent was unable to forward an SNMP trap to the Remote Insight Board trap due to processing error. The data contains the error code.

Event identifier: cpqstmsg.dll - 1806 (Hex) 0x8435070e (Service Event)

Log Severity: Warning (2)

Log Message: The Storage Agent service is not running. The SNMP Agent has determined that the Storage Agent service is not running. Stop the SNMP service and restart the Storage Agents service. If the error persists, reinstalling the Storage Agents may correct this error.

Event identifier: cpqstmsg.dll - 1807 (Hex) 0x4435070f (Service Event)

Log Severity: Information (1)

Log Message: The Storage SNMP Agent has determined the Storage Agents service is running.

Event identifier: cpqstmsg.dll - 1808 (Hex) 0x44350710 (Service Event)

Log Severity: Information (1)

Log Message: The agent could not deliver trap %1. The agent was unable to use Asynchronous Management to deliver a trap. This can be caused by a failure in the Remote Access Service or by a missing or invalid configuration. Use the HPE Insight Management Agents control panel to verify the Asynchronous Management configuration settings. Use the Network control panel to verify the Remote Access configuration. If this error persists, reinstalling the Storage Agents or the Remote Access Service may correct this error. For more information, see the Insight Asynchronous Management documentation.

Event identifier: cpqstmsg.dll - 3584 (Hex) 0x84350e00 (Service Event)

Log Severity: Warning (2)

Log Message: The IDE Agent could not allocate memory. The data contains the error code.

Event identifier: cpqstmsg.dll - 3585 (Hex) 0x84350e01 (Service Event)

Log Severity: Warning (2)

Log Message: The IDE Agent could not open the base of the registry. The data contains the error code.

Event identifier: cpqstmsg.dll - 3586 (Hex) 0x84350e02 (Service Event)

Log Severity: Warning (2)

Log Message: “%1”. The data contains the error code.

Event identifier: cpqstmsg.dll - 3587 (Hex) 0x84350e03 (Service Event)

Log Severity: Warning (2)

Log Message: “%1”. The data contains the error code.

Event identifier: cpqstmsg.dll - 3588 (Hex) 0x84350e04 (Service Event)

Log Severity: Warning (2)

Log Message: The IDE Agent could not read the registry value “%1”. The data contains the error code.

Event identifier: cpqstmsg.dll - 3589 (Hex) 0x84350e05 (Service Event)

Log Severity: Warning (2)

Log Message: The IDE Agent found an incorrect type for registry value “%1”. The data contains the type found.

Event identifier: cpqstmsg.dll - 3590 (Hex) 0x84350e06 (Service Event)

Log Severity: Warning (2)

Log Message: The IDE Agent could not create an event. The data contains the error code.

Event identifier: cpqstmsg.dll - 3591 (Hex) 0x84350e07 (Service Event)

Log Severity: Warning (2)

Log Message: The IDE Agent could not open an event. The data contains the error code.

Event identifier: cpqstmsg.dll - 3592 (Hex) 0x84350e08 (Service Event)

Log Severity: Warning (2)

Log Message: The IDE Agent could not set an event. The data contains the error code.

Event identifier: cpqstmsg.dll - 3593 (Hex) 0x84350e09 (Service Event)

Log Severity: Warning (2)

Log Message: The IDE Agent could not create a mutex. The data contains the error code.

Event identifier: cpqstmsg.dll - 3594 (Hex) 0x84350e0a (Service Event)

Log Severity: Warning (2)

Log Message: The IDE Agent could not open a mutex. The data contains the error code.

Event identifier: cpqstmsg.dll - 3595 (Hex) 0x84350e0b (Service Event)

Log Severity: Warning (2)

Log Message: The IDE Agent could not create its main thread of execution. The data contains the error code.

Event identifier: cpqstmsg.dll - 3596 (Hex) 0x84350e0c (Service Event)

Log Severity: Warning (2)

Log Message: The IDE Agent main thread did not terminate properly. The data contains the error code.

Event identifier: cpqstmsg.dll - 3597 (Hex) 0x84350e0d (Service Event)

Log Severity: Warning (2)

Log Message: The IDE Agent got an unexpected error code while waiting for an event. The data contains the error code.

Event identifier: cpqstmsg.dll - 3598 (Hex) 0x84350e0e (Service Event)

Log Severity: Warning (2)

Log Message: The IDE Agent got an unexpected error code while waiting for multiple events. The data contains the error code.

Event identifier: cpqstmsg.dll - 3599 (Hex) 0x84350e0f (Service Event)

Log Severity: Warning (2)

Log Message: The IDE Agent did not respond to a request. The data contains the error code.

Event identifier: cpqstmsg.dll - 3600 (Hex) 0x84350e10 (Service Event)

Log Severity: Warning (2)

Log Message: The IDE Agent received an unknown action code from the service. The data contains the action code.

Event identifier: cpqstmsg.dll - 4097 (Hex) 0x84351001 (Service Event)

Log Severity: Warning (2)

Log Message: Could not read from the registry subkey. This error can be caused by a corrupt registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4098 (Hex) 0x84351002 (Service Event)

Log Severity: Warning (2)

Log Message: Could not write the registry subkey: “%1”. This error can be caused by a corrupt registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4099 (Hex) 0x84351003 (Service Event)

Log Severity: Warning (2)

Log Message: Could not read the registry subkey: “%1”. This error can be caused by a corrupt registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4100 (Hex) 0x84351004 (Service Event)

Log Severity: Warning (2)

Log Message: Could not read the registry subkey: “%1”. This error can be caused by a corrupt registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4101 (Hex) 0x84351005 (Service Event)

Log Severity: Warning (2)

Log Message: Could not read the registry subkey: “%1”. This error can be caused by a corrupt registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4609 (Hex) 0x84351201 (Service Event)

Log Severity: Warning (2)

Log Message: Could not read the registry subkey. This error can be caused by a corrupt registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4610 (Hex) 0x84351202 (Service Event)

Log Severity: Warning (2)

Log Message: Could not write the registry subkey: “%1”. This error can be caused by a corrupt registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4611 (Hex) 0x84351203 (Service Event)

Log Severity: Warning (2)

Log Message: Could not read the registry subkey: “%1”. This error can be caused by a corrupt registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4612 (Hex) 0x84351204 (Service Event)

Log Severity: Warning (2)

Log Message: Could not read the registry subkey: “%1”. This error can be caused by a corrupt registry or a low memory condition. Rebooting the server may correct this error.

Event identifier: cpqstmsg.dll - 4613 (Hex) 0x84351205 (Service Event)

Log Severity: Warning (2)

Log Message: Could not read the registry subkey: “%1”. This error can be caused by a corrupt registry or a low memory condition. Rebooting the server may correct this error.