Onboard Administrator error messages

Onboard Administrator errors

1 The submitted user already exists.

2 The submitted user name is not valid.

3 The maximum number of users already exists.

5 The requested user does not exist.

6 The submitted group already exists.

7 Invalid privilege level.

8 Insufficient privileges for the requested operation.

10 The submitted user was already enabled.

11 The submitted user was already disabled.

12 The submitted user already has administrator rights.

13 The submitted user is not an administrator.

14 An error occurred while creating a group entry.

16 Unable to perform the operation. Retry the operation or restart OA. (System Error 16)

17 Unable to perform the operation. Retry the operation or restart OA. (System Error 17)

18 Unable to perform the operation. Retry the operation or restart OA. (System Error 18)

19 The submitted bay is already assigned.

20 The submitted bay is not assigned.

22 The submitted value is already in use.

23 The first character in the submitted value is not valid.

24 The submitted value contains an invalid character.

25 The submitted value is too short.

26 The submitted value is too long.

27 The submitted trap receiver already exists.

28 The maximum number of trap receivers already exists.

29 The maximum number of IP managers already exists.

30 The IP Manager already exists.

31 The submitted bay number is out of range.

32 The submitted IP address is not valid.

33 The submitted value is null.

34 An error occurred while generating an event.

35 An error occurred opening the enclosure system log.

36 The submitted date and/or time value was not formatted correctly.

37 An error occurred while opening the Onboard Administrator's system log.

38 The NMI Dump failed for the submitted blade.

39 Setting the UID for the submitted blade failed.

40 Setting the environment variable for the submitted blade failed.

41 Setting the boot order for the submitted blade failed.

42 Setting the power control for the submitted blade failed.

43 Setting the max power for the submitted bladed failed.

44 Shutting down the submitted blade failed.

45 Clearing the submitted blade failed.

46 Getting blade information for the submitted blade failed.

47 Getting blade status for the submitted blade failed.

48 Getting sensor information for the submitted sensor failed.

49 Setting the submitted rack name failed.

50 Getting power supply information for the submitted power supply failed.

51 Getting power supply status for the submitted power supply failed.

52 Getting power supply measurements for the submitted power supply failed.

53 Setting the Onboard Administrator's UID state failed.

54 Getting the Onboard Administrator's status failed.

55 Getting the Onboard Administrator's information failed.

56 Getting fan information for the submitted fan failed.

57 Rebooting the enclosure failed.

58 Shutting down the enclosure failed.

59 Getting the enclosure information failed.

60 Getting the enclosure names failed.

61 Getting the enclosure status failed.

62 Setting the enclosure name failed.

63 Setting the enclosure asset tag failed.

64 Setting the enclosure time zone failed.

65 Setting the enclosure UID failed.

66 Setting the UID for the submitted interconnect failed.

67 Resetting the submitted interconnect failed.

68 Getting interconnect information for the submitted interconnect failed.

69 Getting interconnect status for the submitted interconnect failed.

70 An error occurred while accessing the connected user for the requested blade.

71 An error occurred while reading the lockfile for the submitted blade.

72 The submitted e-mail address is not valid.

73 Libem is not able to talk to iLO.

74 Downloading the submitted file failed.

75 The certificate could not be verified.

76 Could not save the authorization keys.

77 The SSH key size is not correct.

78 Could not ping the requested url.

79 Could not generate the CSR.

80 Could not generate the SSO

81 Could not read the fingerprint.

82 Could not get SSH key.

83 The field is already enabled.

84 The field is already disabled.

85 The system is already in DHCP mode.

86 The system is currently in static IP mode.

87 Could not clear the system log.

88 Could not restore the factory settings.

89 Could not read the configuration file.

90 Could not write to the configuration file.

92 The submitted URL is not valid.

93 Could not update the firmware with the submitted image file.

94 Unable to acquire the rack topology.

95 Invalid domain.

97 Connecting to the blade's iLO failed.

98 Sending the RIBCL command to the requested blade failed.

99 Could not find the requested element in the RIBCL response.

100 Could not find the requested attribute in the RIBCL response.

101 Could not find the starting boundary in the RIBCL response.

102 Could not find the ending boundary in the RIBCL response.

103 Could not determine the IP address of the management processor for the requested blade.

104 Could not locate a Primary NTP server.

105 You must set at least one (1) trusted host before enabling trusted hosts.

107 Could not create the RIBCL request.

108 This error message should be taken from the soap errorText (varies).

118 The management processor auto-login feature is not supported.

119 The maximum number of EBIPA DNS servers has already been reached.

120 The starting IP address and Net Mask must be set before enabling EBIPA.

121 The LDAP group does not exist.

122 The LDAP group already exists.

123 The maximum number of LDAP groups has already been reached.

125 Error getting Insight Display information.

126 Error getting Insight Display status.

127 Error reading the certificate.

128 Error setting the time zone.

129 Error installing the certificate.

130 Exceeded the maximum number of SSO certificates.

131 The X509 Certificate is not formatted correctly.

132 SIM station already in trusted list.

133 SIM station name not found.

134 SIM SSO API received a bad parameter.

135 The maximum number of SIM XE stations already configured.

136 The maximum number of EBIPA interconnects DNS servers has been reached.

137 The session could not be created.

138 The session could not be deleted.

139 Not a valid request while running in standby mode.

140 Not a valid request while transitioning to active mode.

141 Not a valid request while running in active mode.

142 The maximum number of LDAP certificates already exist.

143 Could not remove LDAP certificate.

144 You must configure the directory server and at least one search context before enabling LDAP.

145 Could not set the LDAP group description.

146 An error occurred while communicating with the other Onboard Administrator.

147 Unable to perform the operation. Retry the operation or restart OA. (System Error 147).

148 The other Onboard Administrator is not present.

149 No redundant Onboard Administrator found. Cannot failover.

150 The user could not be authenticated.

151 Invalid parameter for setting blade one time boot.

152 Invalid parameter for setting the blade boot priority.

153 A blade boot device can only be listed once.

154 NTP Poll time must be between 60 and 86400 seconds.

155 Could not create new file.

156 Could not write the file to the disk.

157 The submitted image is too big.

158 The submitted image is not a BMP image.

159 The submitted image does not have the appropriate dimensions.

160 Non-standard BMP images are not supported.

161 The specified item was not found.

162 The protocol specified in the URL is not supported.

163 The upload to the specified URL failed.

164 The Onboard Administrator did not fail over.

165 The blade is in a powered off state.

167 The IP manager does not exist.

168 There is no SSH key installed.

169 There was a problem running the configuration script.

170 Missing credentials.

171 Caught the SIGSEGV signal.

173 No trap receivers were specified.

174 There are no SSH keys installed.

175 There was an error attempting to clear the SSH keys.

176 The IP address is already listed.

177 There was an error getting the SSO trust mode.

178 The submitted SSO trust mode is invalid.

179 The certificate cannot be removed because it does not exist.

180 The interconnect tray is not present.

181 The blade is not present.

182 Users cannot remove or disable themselves.

183 Invalid time zone.

184 Error setting CLP strings.

185 Error getting CLP status.

186 Error setting ISMIC info block.

187 Error reading ISMIC info block.

188 Error clearing blade signature.

189 Error setting blade signature.

190 Request is valid only for server blades.

191 Request is valid only for ProLiant server blades.

192 The string entered is not a valid netmask.

193 The string entered is not a valid gateway.

194 The string entered for DNS server 1 is not valid.

195 The string entered for DNS server 2 is not valid.

196 Error trying to remove a nonexistent SSO name.

197 Error trying to add an SSO name.

198 Invalid SNMP trap community.

201 Could not open the event pipe for reading.

202 Did not read the proper size for events.

203 Event length mismatch.

204 The event listener was terminated.

211 Error obtaining blade power reduction status.

212 Update the other OA firmware to enable this feature.

213 Dates before 14 June 2006 are not valid.

214 The certificate exceeds the maximum valid size.

215 E-Fuse cannot be reset.

216 Firmware update in progress. Login is disabled.

217 An error occurred while setting the enclosure PDU type.

218 An error occurred while setting the enclosure part number.

219 An error occurred while setting the enclosure serial number.

220 Cannot set time when NTP is enabled.

221 Request is valid only for Itanium/BCS/IPF blades.

222 The Active and Standby Onboard Administrator are not the same hardware build.

223 The firmware installed on an Onboard Administrator module is incompatible with FirmwareSync.

224 Failed to create firmware image

225 The Active and Standby Onboard Administrator have the same firmware version installed.

226 Upgrade an Onboard Administrator to firmware 2.10 or later to enable this feature.

227 The requested user cannot be removed from iLO because it is the only remaining administrator account.

228 The requested user cannot be added to iLO because iLO local accounts have been disabled.

229 The requested user cannot be added to iLO because the maximum number of local accounts already exists.

230 One or more of the specified SNMP traps were not already configured on the Onboard Administrator and cannot be removed.

231 Reset Factory Defaults in progress. Login disabled.

232 The requested operation is not available on c3000 enclosures.

233 This feature requires the iLO Select Pack License or iLO Advanced Pack License on the server blade when LDAP is enabled on the Onboard Administrator.

234 Invalid characters detected.

235 Onboard Administrator is initializing. Login disabled.

236 Cannot retrieve Onboard Administrator media device array.

237 The requested device is not ready.

238 Power off or remove the partner blade.

239 The current firmware does not support this operation.

240 Serial number update requires newer firmware version.

241 The requested device is not present or no firmware upgrade is required.

242 The operation cannot be performed on the requested device.

243 iLO license information cannot be retrieved because iLO XML Reply is disabled.

244 SSH is disabled on this blade.

245 Disconnect the virtual media applet.

246 Invalid SNMP Write Community string.

247 Invalid SNMP Read Community string.

248 Invalid port number. The LDAP server SSL port can be any number between 1 and 65535.

249 Feb 29 was specified but the year is not a leap year.

250 The CA certificate is invalid.

251 Exceeded the maximum number of CA certificates.

252 No CA certificates are imported.

253 This CA certificate is already imported.

254 A certificate is already mapped to this user.

255 An undocumented error has occurred. Please update your firmware to the latest firmware version if necessary. Contact Hewlett Packard Enterprise if the problem persists.

256 This certificate is already mapped to another user.

257 The user certificate could not be verified.

258 This operation is not permitted when two-factor authentication is enabled.

260 This operation cannot be performed when AlertMail is disabled.

261 This operation cannot be performed when the AlertMail settings are not configured.

262 This operation cannot be performed when SNMP is disabled.

263 A certificate must be mapped to Administrator or LDAP must be enabled with a configured groups with administrator privilege to enable two-factor authentication.

265 A certificate is not mapped to this user account.

266 Two-factor authentication is in effect.

267 Two-factor authentication configuration was not changed.

268 An iLO image is already staged.

269 The file was not a proper iLO image for the blade.

270 The crc32 supplied does not match the provided file.

271 Cannot delete the last CA with two-factor authentication enabled.

272 The Onboard Administrator cannot communicate with iLO.

273 An EBIPA configuration error occurred.

274 Link Loss Failover intervals must be between 30 and 86400 seconds.

275 Network speed must be either 10Mbit or 100Mbit.

276 Network duplex setting must be HALF or FULL.

277 The password does not conform to password rules.

278 Invalid minimum password value

279 A firmware image is already staged.

280 The provided file was not a proper image.

281 Bad image CRC checksum

282 Remote system logging must be enabled to perform this operation.

283 Invalid remote port. The port must be a number between 1 and 65535.

284 The remote syslog server address must be configured before enabling remote system logging.

285 Invalid remote server address.

286 This setting is already enabled.

287 This setting is already disabled.

288 Enclosure IP mode was not enabled because the active Onboard Administrator does not have a static IPv4 address.

289 This feature is not available for this Onboard Administrator.

290 Request to enable DHCP addressing on the active Onboard Administrator is denied because Enclosure IP Mode is enabled.

291 The value provided is not proper base64.

292 The firmware image provided is an older version than the current firmware. Onboard Administrator settings cannot be preserved.

293 The file provided is not a valid Onboard Administrator firmware image.

294 There are no USB keys connected to the enclosure.

295 No valid firmware images found on USB key.

296 No configuration scripts found on USB key.

297 I/O error on USB key.

298 Badly formatted USB file URL.

299 Permission problems when accessing USB media.

300 Error uploading to USB media.

301 An invalid number of GUIDs was passed to the Onboard Administrator.

302 URL flash image for microcode download not available.

303 Invalid session timeout.

304 Invalid watts value.

305 Failed to store change for power cap.

306 Enclosure Dynamic Power Cap feature is not allowed.

307 Wrong number of bays specified for enclosure while setting capping bays to exclude.

308 The number of bays opted out exceeds the maximum allowed.

309 Enclosure Dynamic Power Cap feature is not allowed.

310 Enclosure Dynamic Power Cap is set.

311 Enclosure Dynamic Power Cap is not set. Cannot confirm that device tray meets minimum firmware version required.

312 Enclosure Dynamic Power Cap not set. Device tray fails to meet the minimum required firmware version.

313 The requested cap is outside the allowable range of Enclosure Dynamic Power Cap values.

314 Server Power Reduction cannot currently be enabled. Enclosure Dynamic Power Cap is not allowed.

315 No valid ISO images found on USB key.

316 Bay privileges cannot be revoked for Administrators with OA permission.

317 Invalid DNS hostname.

318 Factory defaults cannot be restored because the enclosure is in VC mode.

319 The string entered is not a valid IPv6 address.

320 IPv6 static address already exists.

321 IPv6 static address not found.

322 Unable to add.

323 Invalid SMTP server.

324 Invalid SNMP Trap receiver.

325 Invalid NTP server.

326 Invalid EBIPA configuration. Multiple subnets were detected.

327 Specified VLAN ID does not exist.

328 Cannot delete the default VLAN ID.

329 Maximum VLAN entries reached.

330 Duplicated VLAN ID.

331 Specified VLAN ID is invalid.

332 Operation partially successful.

333 Duplicated VLAN name.

334 A pending command already exists.

337 The remote syslog server address cannot be cleared while remote logging is enabled.

338 Invalid search context number.

339 Not on the same VLAN ID domain.

340 This command is not valid for auxiliary blades.

341 No LDAP groups currently exist.

342 The requested Derated Circuit Capacity is outside the allowable range of values for this enclosure.

343 The requested Rated Circuit Capacity is outside the allowable range of values for this enclosure.

344 The requested cap is greater than the requested Derated Circuit Capacity.

345 The requested Derated Circuit Capacity is greater than the requested Rated Circuit Capacity.

346 The requested set of bays to exclude cause the cap to be outside the allowable range.

347 The requested set of bays to exclude cause the Derated Circuit Capacity to be outside the allowable range.

348 The requested set of bays to exclude cause the Rated Circuit Capacity to be outside the allowable range.

353 IPv6 is currently disabled. Cannot download certificate from the specified address.

354 The date cannot be set to a date in the past.

356 The setting cannot be cleared while LDAP is enabled.

357 URB reporting using HTTP(S) cannot be enabled until an HTTP(S) endpoint has been configured.

358 URB reporting using SMTP cannot be enabled until an SMTP server and mailbox have been configured.

359 URB reporting using SMTP and HTTP(S) cannot be enabled until HTTP(S) and SMTP settings have been configured.

360 Warning: Not all VC-Enet modules are on the same VLAN ID.

361 File doesn't exist.

362 This operation cannot be performed when AlertMail is enabled.

363 Setting SolutionsId failed.

364 SolutionsId must be an 8-byte hex string, between 0000000000000000 and FFFFFFFFFFFFFFFF.

365 Failed Remote Support registration.

366 Failed Remote Support un-registration.

367 Failed Remote Support restore registration.

368 Failed to send Remote Support message (Hint: Check the Remote Support proxy and endpoint URL. Use SET REMOTE_SUPPORT PROXY to configure and re-try.)

369 Failed to set Remote Support interval. Valid interval is 0 to 60 (days).

370 You must configure the directory server and SSL port before testing LDAP.

371 The string contains an invalid character.

372 This operation cannot be performed when Remote Support is disabled.

373 Cannot set Maintenance Mode Timeout. Value should be between 5 minutes and 2 weeks.

374 Insert eRs error here.

375 The string entered is not a valid LDAP server. A LDAP server must be a IP address or DNS name.

376 Unable to perform the operation. Retry the operation or restart OA. (System Error 376)

377 The HP Passport credentials provided are invalid.

378 This system is already registered.

379 Please disable Remote Support before performing this action.

380 Transaction UUID is mismatched.

381 Unable to download ilo flash image from the url provided. Supported protocols are http, https, tftp and ftp.

382 The Onboard Administrator is still initializing. Please try your request again later.

383 Failed to send Remote Support message. Please make sure DNS is enabled and verify Insight Remote Support host and port information.

384 Failed to resolve Insight Remote Support hosting server. Please verify DNS settings and Insight Remote Support host and port information.

385 Transmission to the Insight Remote Support receiver was unsuccessful. Please check connectivity between the OA and the Insight Remote Support receiver.

389 This action cannot be performed in FIPS MODE ON/DEBUG.

391 No Variable Name-Value pairs are provided for substitution.

392 Attempted to substitute more than 25 variables.

395 Trying to substitute the same variable twice.

396 String_list searchFlag out of range.

397 No variable names are passed in for searching.

398 No variable values are passed in for searching.

401 Enclosure Firmware Management is currently disabled.

402 The Enclosure Firmware Management ISO URL is not set.

403 The operation cannot be performed while Enclosure Firmware Management is running.

404 Unable to mount ISO or validate version information.

Check URL and validate ISO is available from URL entered.

405 Unable to open firmware log.

406 The blade's firmware has not been discovered.

407 An error occurred while reading the firmware log.

408 Enclosure Firmware Management is not supported by this device type

409 Firmware ISO image is in use, changing URL is not allowed.

410 Blade must be powered off before starting Enclosure Firmware Management.

411 Unable to change passwords for any LDAP or SIM users.

412 Enclosure Firmware Management is not available. To use this feature, it needs to be unlocked.

413 Enclosure Firmware Management is not supported on the Active OA hardware present.

414 Could not persist firmware management log.

415 When in FIPS MODE ON/DEBUG, the password length must be between 8 and 40 characters.

416 When in FIPS MODE ON/DEBUG, strict passwords must be enabled.

417 Certificate hash algorithm is not supported. See OA syslog for more information.

418 Downgrade is not allowed in FIPS Mode ON/DEBUG. Please set FIPS Mode to OFF and retry the operation.

419 Could not persist firmware management log.

427 E-Keying busy.

428 Error getting CLP strings.

431 Enclosure Firmware Management is not ready, please try again in a few minutes.

434 PIN Protection cannot be disabled in FIPS Mode.

435 Cannot restore the factory defaults while in FIPS Mode.

437 Bad EBIPAv6 device.

438 An EBIPAv6 configuration error occurred. Extended information is available as a bitcode reason code.

439 Invalid hash algorithm. The hash algorithm must be one of: SHA1, SHA-224, SHA-256, SHA-384, or SHA-512.

440 You must set a new pin code before unlocking the LCD buttons.

441 The requested operation cannot be completed during a firmware update.

442 This enclosure is incapable of performing a reset on a non-redundant Onboard Administrator.

444 Power cap configuration locked due to active group management.

REMOTE SUPPORT TIER2

445 Remote Support receiver temporarily unavailable. Please retry later.

446 Unregistration request was not processed successfully by the Remote Support receiver. Remote Support has been disabled locally. No service events or data collections will be sent until this device has been re-registered.

447 Authentication error. Please unregister and re-register device.

448 Missing device identifiers. Please unregister and re-register device.

449 Corrupt device identifiers. Please unregister and re-register device.

450 Insufficient device identifier information. Please unregister and re-register device.

451 Invalid device identifier information. Please unregister and re-register device.

452 Stale device identifiers. Please unregister and re-register device.

453 Missing GDID. Please unregister and re-register device.

454 Corrupt GDID. Please unregister and re-register device.

455 Missing registration token. Please unregister and re-register device.

456 Corrupt registration token. Please unregister and re-register device.

457 Expired registration token. Please unregister and re-register device.

458 Invalid HP Passport credentials. Please verify and enter valid HP Passport account credentials.

459 Device is already registered. Please delete the device from Insight Remote Support user interface and retry registration.

460 Unknown device. Please unregister and re-register device.

461 Insufficient registration data. Please retry registration.

462 Missing SOAP header. Please retry your last step. If error persists and device is currently registered, unregister and re-register device.

463 Missing GUID. Please retry your last step. If error persists and device is currently registered, unregister and re-register device.

464 Corrupt GUID. Please retry your last step. If error persists and device is currently registered, unregister and re-register device.

465 Missing data package. Please retry your last step. If error persists and device is currently registered, unregister and re-register device.

466 Data Package validation failed. Please retry your last step. If error persists and device is currently registered, unregister and re-register device.

467 HP Passport password must be changed or reset. Please attempt to register again after correcting the HP Passport account issue.

468 Expired HP Passport credentials. Please attempt to register again after correcting the HP Passport account issue.

469 HP Passport account locked out. Please attempt to register again after correcting the HP Passport account issue.

470 GDID and device identifiers do not match. If error persists and device is not currently registered, unregister and re-register device.

471 Device is not registered. Remote Support registration has been disabled locally on this device. No service events or data collections will be sent until this device has been re-registered.

472 Deleted device. This device has been previously deleted from the Insight Remote Support user interface. Please unregister and re-register device.

473 Unhandled Error.

474 Failed to connect to Insight Remote Support direct connect web service. Please verify DNS settings, proxy settings and connectivity.

475 Dynamic DNS is not enabled.

476 Invalid SNMP Engine ID. The Engine ID must start with '0x' followed by an even number of up to 64 hexadecimal digits.

477 Invalid Authentication Protocol.

478 Invalid Authentication Password, must contain 8 to 40 printable characters.

479 Invalid Privacy Protocol.

480 Invalid Privacy Password, must contain 8 to 40 printable characters.

481 Duplicate user, a SNMP user by this name and engine id already exists.

482 Invalid minimal security setting.

483 Invalid security setting.

484 Selected algorithm cannot be used while FIPS Mode is enabled.

485 A user with read-write access cannot be created while FIPS Mode is enabled.

486 You cannot use a remote engine id with a trap.

487 You cannot use the local engine id with an inform.

489 Error adding the language pack.

490 Error removing the language pack.

491 The file provided is not a valid Onboard Administrator language pack image.

492 Cannot remove the English language pack.

493 The language support pack is not installed.

494 The submitted file is not a valid SSH key.

499 The firmware image provided doesn't meet the VC Minimum Firmware Version requirement. Check the OA Syslog for more details.

500 The action did not complete successfully.

502 Invalid response. No connection or network busy.

503 Web server busy or in service.

510 Remote Support services are provided by other solution.

511 DHCP-Supplied Domain Name cannot be disabled when the user-supplied domain name is not set.

512 The text must contain at least one visible character.

514 User ID is a required field. Please retry registration.

515 The user must have an active authenticated session. Please retry registration.

516 HP Passport system failure occurred. A problem has been detected in the HP Passport system. Please retry later.

517 The session token is invalid due to any of the following reasons: failed decoding, token is null or empty, userId is empty or session start value is not a number. Please retry registration.

518 Password is required. Please retry registration.

519 HP Passport user ID is invalid. Please retry registration with a valid user ID.

520 HP Passport account is locked out due to excessive login authentication failures. Please reset your password and retry registration.

521 User has reached half the maximum allowed HP Passport login authentication failures. Please verify your username and password are correct and retry registration.

522 HP Passport password has expired. Please update your password and retry registration.

523 User has at least one of the HP Passport required on-line identity elements missing. Please update your HP Passport profile and retry registration.

524 HP Passport Security Q and A is not compliant; the user must enter a new security Q and A upon login. Please update your HP Passport security Q and A and retry registration.

525 HP Passport password entered is incorrect. Please retry registration using the correct password.

526 HP Passport user has been added to a group. Please reset your password and retry registration.

527 User must enter an HP Passport security Q and A and change password. Please update your security Q and A, update your password, and retry registration.

528 Protocol error occurred while communicating with the Insight Remote Support receiver.

529 Failed to resolve proxy. Please verify DNS settings, proxy settings and connectivity.

530 Failed to connect to the Insight Remote Support hosting server. Please verify Insight Remote Support host and port information.

531 Failed to connect to the Insight Remote Support direct connect web service. Please verify DNS settings, proxy settings and connectivity.

532 Remote Support receiver protocol error.

533 The setting cannot be cleared when user domain name is enabled.

534 The operation cannot be performed while Enclosure Firmware Management is enabled.

535 Invalid SNMP Engine ID string. The Engine ID string must contain 1 to 27 printable characters.

536 The password is too short.

537 The password is too long.

538 Error installing the certificate.

539 Enclosure IP mode requires the active Onboard Administrator to have a static IPv4 address or a static IPv6 address. If IPv6 is not enabled, only the static IPv4 address can be used.

540 Configure a static IPv6 address for your active OA or disable Enclosure IP Mode before enabling DHCP for IPv4.

541 Configure a static IPv4 address for your active OA or disable Enclosure IP Mode before disabling IPv6.

542 The submitted URL is invalid for uploading.

543 This version of Onboard Administrator firmware does not support boot options for servers configured in UEFI Boot mode.

561 Transmission from the Insight Remote Support receiver was unsuccessful.

562 Transmission from the Insight Remote Support receiver was unsuccessful. Please check connectivity between OA and the Insight Remote Support receiver.

563 The key strength for the provided key is invalid for this configuration.

564 This command is not supported by the interconnect.

565 The string entered is a link-local address and cannot be used for assignment.

566 Invalid IPv6 static route gateway. Route gateway must not be empty and must not contain prefix length.

567 IPv6 static route destination already exists.

568 Unable to add IPv6 route. The maximum number of IPV6 static routes already exist.

569 IPv6 static route not found.

570 Invalid IPv6 static route destination. The route destination must be a valid IPv6 address.

571 All items cannot be disabled.

572 This action requires the OA to be in FIPS Mode ON/DEBUG.

573 Must set MINRATE option if using timeout range.

574 Minimum data rate must be larger than 0.

575 Maximum timeout must be larger than minimum timeout.

576 Timeout must be larger than 0.

577 HTTP Read Timeout is already set to the requested value.

Insight Display screen shot errors

1 Missing credentials.

2 The getLCDImage CGI process has caught the SIGSEGV signal.

3 Could not acquire access to the image in a reasonable amount of time.

4 Cannot open semaphores.

5 Produce SEMV does not work.

6 Consume SEMV does not work.

7 Cannot lock the image file.

8 Cannot open the image file.

9 Cannot seek in the image file.

10 Unable to resume session.

11 Insufficient privileges.