HPE ProLiant DL160 Gen10 Server User Guide
Component identification
Front panel components
Four-bay LFF drive model
Eight-bay SFF drive model with optical drive
Eight-bay SFF drive model with two-bay SFF option
Serial number/iLO information pull tab
Front panel LEDs and buttons
Four-bay LFF drive model
Eight-bay SFF model
Power fault LEDs
Rear panel components
Rear panel LEDs
PCIe expansion slot definitions
PCIe slot description
System board components
System maintenance switch descriptions
DIMM label identification
Processor, heatsink, and socket components
Drive bay numbering
Four-bay LFF drive model
Eight-bay SFF drive model with optical drive
Eight-bay SFF drive model with two-bay SFF option
Drive LEDs and buttons
Low-profile LFF drive LED definitions
Smart Carrier (SC) drive LED definitions
Fan locations
Operations
Power up the server
Power down the server
Extend the server from the rack
Access the product rear panel
Opening the cable management arm
Remove the server from the rack
Removing the front bezel
Remove the access panel
Install the access panel
Removing the primary PCI riser blank
Installing the primary PCI riser blank
Removing the primary PCI riser cage
Installing the primary PCI riser cage
Removing the secondary PCI riser cage
Installing the secondary PCI riser cage
Removing the expansion slot blank
Removing and replacing a drive blank
Setup
Optional service
Initial
server
installation
HPE Installation Service
Setting up the server
Operational requirements
Space and airflow requirements
Temperature requirements
Power requirements
Electrical grounding requirements
Server warnings and cautions
Rack warnings
Electrostatic discharge
Installing the
server
into the rack
POST screen options
Operating system
Installing the operating system with Intelligent Provisioning
Installing or deploying an operating system
Hardware options installation
Introduction
Installing the front bezel option
Redundant power supply enablement option
Installing the redundant power supply enablement kit
Power supply options
Hot-plug power supply calculations
Installing a hot-plug AC power supply
Memory options
Installing a DIMM
Drive options
Hot-plug drive guidelines
Drive support information
Installing a hot-plug SAS or SATA drive
Installing a two-bay SFF enablement kit
Redundant fan option
Fan population guildlines
Fan mode behavior
Installing a fan
Installing the optical drive
Installing the Media Module adapter
Installing the FlexibleLOM adapter
Installing the serial port
Expansion board options
Installing an expansion board
Storage controller options
Installing a Smart Array modular controller
Installing a Smart Array PCIe plug-in controller
Configuring an HPE Smart Array Gen10 controller
Processor heatsink assembly option
Processor cautions
Installing a processor heatsink assembly
Enable the enhanced cooling function
Installing the chassis intrusion detection switch
Energy pack options
HPE Smart Storage Battery
HPE Smart Storage Hybrid Capacitor
Installing an energy pack
M.2 SSD enablement option
Installing the M.2 SSD enablement board
HPE Trusted Platform Module 2.0 Gen10 option
Overview
HPE
Trusted Platform Module 2.0 guidelines
Installing and enabling the HPE TPM 2.0 Gen10 option
Cabling
Cabling guidelines
Four-bay LFF drive model cabling
Four-bay LFF drive backplane cabling
Optical drive cabling
Front I/O and thermal ambient sensor cabling
USB 3.0 cabling
iLO Service Port cabling
Eight-bay SFF drive model cabling
Eight-bay SFF drive backplane cabling
Two-bay SFF SAS/SATA drive cage cabling
Optical drive cabling
Front I/O and thermal ambient sensor cabling
USB 3.0 cabling
iLO Service Port cabling
M.2 SATA SSD cabling
Controller backup power cabling
Serial port cabling
Energy pack cabling
Chassis intrusion detection switch cabling
Software and configuration utilities
Server mode
Product QuickSpecs
Active Health System Viewer
Active Health System
HPE
iLO 5
iLO
Federation
iLO
Service Port
iLO
RESTful API
RESTful Interface Tool
iLO Amplifier Pack
Integrated Management Log
Intelligent Provisioning
Intelligent Provisioning operation
Management security
Scripting Toolkit for Windows and Linux
UEFI System Utilities
Selecting the boot mode
Secure Boot
Launching the Embedded UEFI Shell
HPE Smart Storage Administrator
HPE InfoSight for servers
USB support
External USB functionality
Redundant ROM support
Safety and security benefits
Keeping the system current
Updating firmware or system ROM
Drivers
Software and firmware
Operating system version support
HPE Pointnext Portfolio
Proactive notifications
System battery replacement
System battery information
Removing and replacing the system battery
Troubleshooting
NMI functionality
Troubleshooting resources
Specifications
Environmental specifications
Mechanical specifications
Power supply specifications
HPE 500W Flex Slot Platinum Hot-plug Low Halogen Power Supply
HPE 800W Flex Slot Platinum Hot-plug Low Halogen Power Supply
HPE 800W Flex Slot Titanium Hot-plug Low Halogen Power Supply
HPE 800W Flex Slot Universal Hot-plug Low Halogen Power Supply
HPE 800W Flex Slot -48VDC Hot Plug Low Halogen Power Supply
Websites
Support and other resources
Accessing Hewlett Packard Enterprise Support
Accessing updates
Remote support
Warranty information
Regulatory information
Documentation feedback
Version
Search
Home
Cabling
Controller backup power cabling
Controller backup power cabling
nonav
nonav
