HPE Apollo 4200 Gen10
System
User Guide
Component identification
Front panel components
Rear panel components
Rear panel LEDs
System board components
DIMM slot locations
DIMM label identification
HPE Persistent Memory module label identification
System maintenance switch descriptions
NMI functionality
Front panel LEDs and buttons
UID button functionality
Front panel LED power fault codes
Drive numbering
Drive LEDs
Low-profile LFF drive LED definitions
SFF drive components and LEDs
NVMe drive components and LEDs
SFF flash adapter components and LED definitions
Drive cage identification
Drive cage backplane identification
M.2 SSD slot numbering
HPE Smart Array P824i-p MR Gen10 Controller
HPE InfiniBand HDR/Ethernet 940QSFP 56x16 adapter LEDs
DSC-25 2-port SFP28 card ports and LEDs
HPE NS204i-p NVMe OS Boot Device components
HPE NS204i-p NVMe OS Boot Device LED definitions
Fan locations
Fan numbering
Operations
Power down the system
Remove the bezel
Extend the front drive cages out of the chassis
Slide the front drive cages into the chassis
Removing a drive
Remove the system from the rack
Remove the access panel
Install the access panel
Open the cable management holder
Remove the HPE Smart Storage Battery
Remove the air baffle
Install the air baffle
Close the cable management holder
Remove the rear drive cage blank
Remove the air blocker from PCIe expansion slots 5–7
Remove the PCIe riser cage
Remove a rear drive cage
Setup
HPE support services
Set up the system
Operational requirements
Space and airflow requirements
Temperature requirements
Power requirements
Electrical grounding requirements
System warnings and cautions
Rack warnings and cautions
Remove the shipping screws
Installing hardware options
Installing the system into the rack
Power up the system
Installing the operating system
Selecting boot options in UEFI Boot Mode
Registering the server
Hardware options installation
Product QuickSpecs
Introduction
Installing the security bezel
Drive options
Installing a drive
Drive cage options
Drive cage installation alerts
Installing the four-bay LFF hot-plug rear drive cage
Installing the two-bay SFF hot-plug rear drive cage and two-slot PCIe riser cage
Installing the six-bay SFF NVMe rear drive cage
Installing the six-bay SFF rear drive cage (SAS, SATA)
M.2 SSD enablement board option
Installing the M.2 SSD enablement board
Expansion slots
Supported PCIe form factors
Installing an expansion board or type -p controller
Installing an HPE InfiniBand HDR/Ethernet 200Gb 1-port 940QSFP56 x16 Adapter
Installing the HPE NS204i-p NVMe OS Boot Device option
Installing the Pensando DSP DSC-25 2p SFP28 card
Controller options
Installing a storage controller
Installing a processor-heatsink assembly
Memory options
DIMM population information
DIMM-processor compatibility
HPE SmartMemory speed information
DIMM label identification
Installing a DIMM
HPE Persistent Memory option
Internal USB device option
Power supply option
Installing a DC hot-plug power supply
Installing an AC hot-plug power supply
HPE Smart Storage Battery
Installing the HPE Smart Storage Battery
HPE Trusted Platform Module 2.0 Gen10 option
Overview
HPE Trusted Platform Module 2.0 guidelines
Installing and enabling the HPE TPM 2.0 Gen10 option
Cabling
Cabling overview
Front drive cage cabling
Front and internal drive cage cabling
Internal drive cage cabling
Rear LFF drive cage cabling
Rear SFF drive cage cabling
Rear six-bay SFF drive cage cabling (SAS, SATA)
NVMe rear drive cage cabling
M.2 SSD Enablement option cabling
HPE Smart Array P824i-p MR Gen10 cabling
HPE Smart Storage Battery cabling
iLO ports to network cabling
Fan assembly cabling
Front panel cabling
Software and configuration utilities
Server mode
Product QuickSpecs
Active Health System Viewer
Active Health System
HPE iLO 5
iLO Federation
iLO Service Port
iLO RESTful API
RESTful Interface Tool
iLO Amplifier Pack
Intelligent Provisioning
Management security
Scripting Toolkit for Windows and Linux
UEFI System Utilities
Selecting the boot mode
Secure Boot
Launching the Embedded UEFI Shell
HPE Smart Storage Administrator
HPE MR Storage Administrator
HPE InfoSight for servers
StorCLI
USB support
External USB functionality
Redundant ROM support
Safety and security benefits
Keeping the system current
Updating firmware or system ROM
Drivers
Software and firmware
Operating system version support
HPE Pointnext Portfolio
Proactive notifications
Troubleshooting
Troubleshooting resources
System battery replacement
Replace the system battery
Electrostatic discharge
Specifications
Environmental specifications
Mechanical specifications
Power supply specifications
Hot-plug power supply calculations
Websites
Support and other resources
Accessing Hewlett Packard Enterprise Support
Accessing updates
Remote support
Warranty information
Regulatory information
Documentation feedback
Version
Search
Home
Setup
Power up the system
Power up the
system
To power up the
system
, press the Power On/Standby button.
nonav
nonav