HPE Virtual Connect SE 100Gb F8 Module for HPE Synergy LEDs and buttons



Item Description Status
1 Interconnect link port LEDs

Solid green = Linked

Solid red = Error detected1.

Off = No link

2 QSFP28 uplink port LEDs

If the port is in 40GbE or 100GbE mode, only the leftmost LED lights up when linked.

The four LEDs above each port correspond to the 10/25GbE or 8Gb/16Gb/32Gb FC channels of the port. The LEDs display one of four modes:
Ethernet ID mode:

  • Solid green = The port is configured as an Uplink port.

  • Solid orange = The port is configured as a Stacking Link port.

  • Solid magenta = Configured as a Mirror to port.

  • Off = The port is not configured as an Ethernet port.

PID mode:

  • Solid green = The port is configured for Ethernet.

  • Solid orange = The port is configured for Fibre Channel.

  • Solid red = error.

  • Off = The port is not configured.

Link/Activity mode:

  • Solid green =
    • 10Gb Ethernet link without activity
  • Flashing green =
    • 10Gb Ethernet activity
  • Solid orange =
    • 25Gb Ethernet link without activity
    • 8Gb FC link without activity
  • Flashing orange =
    • 25Gb Ethernet link with activity
    • 8Gb FC link with activity
  • Solid magenta =
    • 40Gb Ethernet link without activity
    • 16Gb FC link without activity
  • Flashing magenta =
    • 40Gb Ethernet link with activity
    • 16Gb FC link with activity
  • Solid cyan =
    • 100Gb Ethernet link without activity
    • 32Gb FC link without activity
  • Flashing cyan =
    • 100Gb Ethernet link with activity
    • 32Gb FC link with activity

  • Off = No link or not configured

Fibre Channel (FC) ID mode:

  • Solid green = Logged into Attached Switch.

  • Solid orange = Not logged into Attached Switch.

  • Off = The port is not configured as an FC port.

To switch between the LED modes, press the Mode button.

3 SFP+ Image Streamer port LEDs

Left LED

Link/Activity mode:
  • Off = No Link

  • Solid green = Ethernet linked at 10Gb

PID:

  • Off = Not configured

  • Solid blue = Port ID

  • Solid green = Configured for Ethernet

  • Solid red = Error

Ethernet:

  • Off = Not Ethernet

  • Solid green = Configured for Ethernet

Fibre Channel:

  • Always off

Right LED

Link/Activity mode:

  • Off = No activity

  • Flashing green = Activity at 10Gb

PID:

  • Always off

Ethernet:

  • Always off

Fibre Channel:

  • Always off

4 Fibre Channel (FC) mode LED Solid green = FC mode is selected.
5

Ethernet mode LED

Solid green = Ethernet mode is selected.
6 PID mode LED Solid green = PID mode is selected.
7 Link/Activity mode LED2 Solid green = Link/Activity mode is selected.
8 Health LED

Solid green = Normal

Flashing amber = There is a fault condition

Flashing red = Critical fault detected

Solid red = No power present

9 Mode button Press and hold the Mode button for more than 5 seconds to reset.

Solid green = There are four LEDs that indicate the operating mode for the Port LEDs. The operating mode is selected by pressing the Mode button on the front panel. The LED mode state determines which of the four Mode LEDs is lit.

10 UID LED

Solid blue = Activated

Flashing blue = Firmware upgrade in progress

Off = Deactivated

1

See HPE OneView (

http://www.hpe.com/info/oneview/docs

)

2

When illuminated, the QSFP28 port LEDs indicate the port operating states for each of the uplink ports in the selected mode.